收藏本站
AS1106, AS1107
Datasheet - D e t a i l e d D e s c r i p t i o n
8 Detailed Description
8.1 AS1106 vs. AS1107
The AS1106 and AS1107 are identical except for two features:
The AS1107 segment drivers are slew-rate limited to reduce electromagnetic interference (EMI).
The AS1107 serial interface is fully SPI compatible (programmable for AS1106).
8.2 Serial-Addressing Format
Programming the AS1106/AS1107 is done by writing to the device’s internal registers (see Digit- and Control-Registers on page 9) via the 4-wire
serial interface. A programming sequence consists of 16-bit packages as listed in Table 6 .
The data is shifted into the internal 16-bit register with the rising edge of the CLK signal. With the rising edge of the LOAD/CSN signal the data is
latched into a digit- or control-register. The LOAD/CSN signal must go high after the 16th rising clock edge.
The LOAD/CSN signal can also come later but this must happen just before the next rising edge of CLK, otherwise the data will be lost. The
contents of the internal shift register are applied 16.5 clock cycles later to pin DOUT. The data is clocked out at the falling edge of CLK.
The first 4 bits (D15:D12) are “don't care”, bits D11:D8 contain the register address, and bits D7:D0 contain the data. The first bit is D15, the most
significant bit (MSB). The exact timing is shown in Figure 12 .
Table 6. 16-Bit Serial Data Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
Register Address (see Table 7 )
MSB
Data
LSB
8.3 Initial Power-Up
On initial power-up, the AS1106/AS1107 registers are reset to their default values, the display is blanked, and the device goes into shutdown
mode. At this time, all registers should be programmed for normal operation.
Note: The default settings enable only scanning of one digit; the internal decoder is disabled and the Intensity Control Register (see page 12)
is set to the minimum values.
Figure 12. Interface Timing
LOAD/CSN
t CSW
t CSH
t CSS
t CL
t CH
t CP
t LDCK
CLK
t DS
t DH
DIN
D15
D14
D1
D0
t DO
DOUT
www.austriamicrosystems.com/LED-Driver-ICs/AS1106_07
Revision 2.28
8 - 21
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AS1109 EB BOARD EVAL AS1109
AS1110 EB BOARD EVAL AS1110
AS1112 EB BOARD EVAL AS1112
AS1115 DB-YELLOW BOARD DEMO AS1115 YELLOW
AS1116 DB-YELLOW BOARD DEMO AS1116 YELLOW
AS3691A EB BOARD EVAL AS3691A
AS5030 DB BOARD DEMO AS5030
AS5048-DB-1.0 BOARD DEMO AS5048
相关代理商/技术参数
AS11070FLF 制造商:TT Electronics / IRC 功能描述:AS11070FLF
AS11070HLF 制造商:TT Electronics / IRC 功能描述:AS11070HLF
AS11070JLF 制造商:TT Electronics / IRC 功能描述:AS11070JLF
AS11071FLF 制造商:TT Electronics / IRC 功能描述:AS11071FLF
AS11071HLF 制造商:TT Electronics / IRC 功能描述:AS11071HLF
AS11071JLF 制造商:TT Electronics / IRC 功能描述:AS11071JLF
AS1107DB 功能描述:显示开发工具 RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V
AS1107-DB 功能描述:显示开发工具 AS1107 Demo Board RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V